Peugeot 208 Key Replacement
Peugeot 208 key replacement is best left to experienced auto locksmiths who have the proper tools and know-how. They can program and create keys faster and cheaper than dealers.
A dead battery for your coin is most likely to be the cause if your key fob stops locking or unlocking the doors. There are other reasons why the key might be malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as preventing it from starting the engine. If this is the scenario, you'll need make use of the backup starting procedure that is described in your vehicle's owner manual.
The spark plugs may also be worn out. The spark plugs are responsible for sparking the fuel that starts the engine. However they have a finite life span. They'll eventually degrade when they aren't used enough.
There is a straightforward solution to this issue. Check the voltage of your battery with a multimeter. If it's lower than 11.5 volts and you are not satisfied, then it is time to replace it. It is also necessary to clean the contacts of the battery in case it is corroded. This can be done by lifting the rubber covers that cover the two battery terminals and using a wire brush to remove any corroded components of the battery. Then, reconnect the cables to the positive and negative poles.
Water Damage
If your 208 won't start and the battery has not failed, you should examine the spark plugs. It is possible that they are just overly dirty, which causes them not to spark. This can be fixed by cleaning the spark plugs in a workshop.
Peugeot cars are equipped with a key with a transponder that is compatible with the immobiliser. This ensures that only a valid key can turn the engine. If the chip inside the Peugeot key is damaged, it will not send the correct signal to the vehicle.
This is a frequent issue that can be caused by water damage. This is a typical issue in colder climates where the vehicle has been exposed to snow or rain. If this is the case, you should call a reputable auto locksmith who will have all the tools and equipment required to reprogram the new key. They also have the most up-to-date technological know-how and the equipment required to create a Peugeot 208 smart key. The process shouldn't last more than 15 minutes.
Faulty Battery Contacts
Peugeot replaced the transponder chips using a new model that utilizes electronic components mounted on a circuitboard. This new system works great when it's fresh, but over time the circuit boards begin to lose their effectiveness and cease working correctly.
This can stop the immobiliser from triggering so that your vehicle will not start. If this happens it's recommended to call a Peugeot specialist or locksmith.
A common issue occurs when the battery in the key fob starts to fail. This causes the blade of the key to stop feeding into the lock. A locksmith from your vehicle can replace the battery and cut a new blade for you, it's usually a simple fix.
Faulty Receiver Module
It could be that the receiver module has a problem in the event that your Peugeot key fob stops working after being dropped on the floor, or exposed to a stormy rainstorm, or accidentally washed. The receiver module is responsible for transmitting radio frequency to the onboard computer which controls the central locking system of your Peugeot vehicle.
Rubber seals on the key fob block water from getting to the electronic chip. Water can damage the chip when exposed to water for a prolonged period of time. Submerging the key fob into ocean water on the beach or throwing it into the water can be particularly damaging due to the high salt content.
The module will need to be replaced if the Peugeot spare key no longer works. This can only by done by an Peugeot specialist or an expert auto locksmith. Peugeot keys unlike other automobiles, are protected by an immobilizer system. This requires the right code to begin the car. This is the reason why you should only choose a reputable Peugeot locksmith to handle the task of programming and creating the replacement.
Computer malfunctioning on-board
The on-board computer in your Peugeot is responsible for many of the systems inside your car, ranging from power windows to the airbags. The computer on board will display an error code when something goes wrong. The code is stored within the system and will remain there until the issue is resolved. In most cases, this will require the on-board computer being replaced.
One of the most frequent causes of the airbag light turning on is the loose or corroded connectors in the airbag sensor. peugeot 207 key fob G28 could be due to wear and tear, aging, exposure to salt and moisture. This issue must be taken care of as soon as you can, because an airbag that's malfunctioning could be dangerous in case in the event of an accident.
If your Peugeot is showing a card detected as not present error, then the key battery inside the key fob might be weak or dead. This will stop the key fob sending a signal to deactivate the immobilizer on your vehicle. You can test this by pressing the unlock button on the key fob and then trying to start your car. If this fails it is likely that the battery is in need of replacement.